สินค้า

QL5

32 + 2 fader configuration adapts to a wide range of channel layouts. The QL5 is a compact console with large-scale capabilities.

Category:

Description

  • Mix channels: 64 mono, 8 stereo.
  • Busses: 16 mix, 8 matrix (Input to Matrix supported).
  • Local I/O: 32 in, 16 out.
  • Fader configuration: 32 + 2 (Master).
  • Stainless steel iPad support stays.

ข้อมูลจำเพาะ

General specifications

Sampling frequency rate Internal 44.1kHz / 48kHz
External 44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm)
Signal delay Less than 2.5ms, INPUT to OMNI OUT, Fs= 48kHz
Fader 100mm motorized, Resolution=1024steps, +10dB to –138dB, –∞dB all faders
Total harmonic distortion Less than 0.05% [email protected]+4dBu into 600Ω, INPUT to OMNI OUT, Input Gain= Min.
Frequency response +0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUT
Dynamic range 112dB typ.: DA Converter / 108dB typ.: INPUT to OMNI OUT, Input Gain = Min.
Hum & noise level Equivalent input noise -128dBu typ., Equivalent Input Noise, Input Gain=Max
Residual output noise -88dBu, Residual output noise, ST master off
Crosstalk -100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min.
Power requirements 100-240V 50/60Hz
Power consumption 200W
Dimensions W 828mm(32.6in)
H 272mm(10.7in)
D 563mm(22.2in)
Net weight 21.8kg(48.1lb)
Accessories Owner’s Manual, dust cover, power cord, DVS license sheet
Options Mini-YGDAI cards *2 , Gooseneck Lamp LA1L, Nuendo Live
Others Operating temperature range: 0 – 40℃, Storage temperature range: -20 – 60℃

[email protected] : A 22kHz, 30dB/Oct filter is used to measure crosstalk.
Total Harmonic Distortion : An 80kHz, 18dB/Oct filter is used to measure total harmonic distortion.
Hum & Noise : An A-Weight filter is used to measure hum &noise.

Analog input characteristics

Input Connectors GAIN Input
Impedance
Source
Impedance
Input level Connector
Sensitivity*¹ Nominal Max. before clip
INPUT
1-32 *6
+66dB 7.5 kΩ 50-600 Ω
Mics &
600 ΩLines
–82dBu
(61.6μV)
–62dBu
(0.616mV)
–42dBu
(6.16mV)
XLR-3-31
type
(Balanced) *2
–6dB –10dBu
(245mV)
+10dBu
(2.45V)
+30dBu
(24.5V)

*1. The sensitivity is the input level required for output at +4dBu (1.23V) or at the defined level when all the faders and level
controllers are set to the maximum value.
*2. XLR-3-31 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*3. 0dBu=0.775 Vms for all specifications.
*4. All the AD converters use 24-bit linear/128-times oversampling.
*5. The INPUT connectors have +48V DC (phantom power) jacks, each of which can be turned on/off individually from the console software.
*6. QL1: INPUT1-16

Analog output characteristics

Output
Connectors
Output
Impedance
Load
Impedance
Maximum
Output
Level *5
Output Level Connector
Defined Level Maximum
Non-Clip Level
OMNI
OUT 1-16 *7
75 Ω 600 Ω
Lines
+24dB
(default)
+4dBu
(1.23V)
vt+24dBu
(12.3V)
XLR-3-32 type
(Balanced) *1
+18dB –2dBu
(616mV)
+18dBu
(6.16V)
PHONES 15 Ω 8 Ω
Phones
75mW *6 150mW Stereo Phone
Jack(TRS)
(Unbalanced) *2
40 Ω
Phones
65mW *6 150mW

*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*2. The PHONES connectors for stereo headphones are balanced jacks (Tip=LEFT, Ring=RIGHT, Sleeve= GND).
*3. 0 dBu=0.775 Vms for all specifications.
*4. All the DA converters use 24-bit linear/128-times oversampling.
*5. The console has an internal switch for toggling the maximum output level.
*6. This is a value measured with the PHONES LEVEL knob set to 10 dB below the maximum position.
*7. QL1: OMNI OUT 1-8

Digital input/output specifications

Connectors Format Data length Level Audio Connector
Primary/Secondary Dante 24bit or 32bit 1000Base-T 64ch Input/64ch
[email protected] *1
EtherCON Cat5e

*1. QL1: 32ch Input/32ch [email protected]

Digital output specifications

Connectors Format Data length Level Connector
DIGITAL OUT AES/EBU AES/EBU Professional Use 24bit RS422 XLR-3-32 type (Balanced) *1

*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).

I/O SLOT (1-2) specifications

Each I/O Slot accepts a Mini-YGDAI card.
Only Slot 1 has a serial interfac

Control I/O characteristics

Connectors Format Level Connector
MIDI IN MIDI DIN Connector 5P
OUT MIDI DIN Connector 5P
WORDCLOCK IN TTL/75 Ω terminated BNC Connector
OUT TTL/75 Ω BNC Connector
GPI (5IN/5OUT) D Sub Connector 15P(Female) *1
NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45
LAMP (QL5: x 2, QL1: x 1) 0V-12V XLR-4-31 type *2
USB HOST USB 2.0 USB A Connector (Female)

*1. Input pin: TTL level, w/ internal pull-up (47kΩ) Output pin: Open drain output (Vmax=12V, maximum sink current/pin=-75mA) Power supply pin: Output voltage Vp=5V, Max. output current=300mA
*2. 4 pin=+12V, 3 pin=GND, Lamp nominal power: 5W, Brightness (voltage) can be adjusted from the software.

Reviews

There are no reviews yet.

Be the first to review “QL5”

Your email address will not be published. Required fields are marked *

  • หมวดสินค้า

    • No product categories exist.
  • ยี่ห้อ